- 您现在的位置：买卖IC网 > Sheet目录341 > MAX5092EVKIT+ (Maxim Integrated Products)KIT EVALUATION FOR MAX5092
4V to 72V Input LDOs with Boost Preregulator
I × 2 . 7 × 10 ? 6
L ≤ IN ON MAX
Design Guidelines
Input Capacitor (C IN ) and
Boost Capacitor (C BSOUT ) Selection
The input current waveform of the boost converter is
continuous, and usually does not demand high capaci-
tance at its input. However, the MAX5092_/MAX5093_
boost converter is designed to fully turn on as soon as
the input drops below a certain voltage in order to ride
out cold-crank droops. This operation demands low
input source impedance for proper operation. If the
source (battery) is located far from the IC, high-capaci-
ty, low-ESR capacitors are recommended for C IN . The
worst-case peak capacitor current could be as high as
3A. Use a 47μF, 100m Ω low-ESR capacitor placed as
close as possible to the input of the device. Note that
the aluminum electrolytic capacitor ESR increases sig-
nificantly at cold temperatures. In the cold temperature
case, choose an electrolyte capacitor with ESR lower
than 40m Ω or connect a low-ESR ceramic capacitor
(10μF) in parallel with the electrolytic capacitor.
The boost converter output (BSOUT) is fed to the input
of the internal 250mA LDO. The boost-converter output
current waveform is discontinuous and requires high-
capacity, low-ESR capacitors at BSOUT to ensure low
V BSOUT ripple. During the on-time of the internal MOSFET,
the BSOUT capacitor supplies 250mA current to the
LDO input. During the off-time, the inductor dumps cur-
rent into the output capacitor while supplying the output
load current. The internal 250mA LDO is designed with
high PSRR; however, high-frequency spikes may not be
rejected by the LDO. Thus, high-value, low-ESR elec-
trolytic capacitors are recommended for C BSOUT .
Peak-to-peak V BSOUT ripple depends on the ESR of the
electrolyte capacitor. Use the following equation to cal-
culate the required ESR (ESR BSOUT ) of the BSOUT
capacitor:
where Δ V ESRBS is 75% of total peak-to-peak ripple at
BSOUT, I LIM is the internal switch current limit (3A max),
and I OUT is the LDO output current. Use a 100m Ω or
lower ESR electrolytic capacitor. Make sure the ESR at
cold temperatures does not cause excessive ripple
voltage. Alternately, use a 10μF ceramic capacitor in
parallel with the electrolyte capacitor.
During the switch on-time, the BSOUT capacitor dis-
charges while supplying I OUT . The ripple caused by
the capacitor discharge ( Δ V CBS ) is estimated by using
the following equation:
Δ V CBS = OUT
C BSOUT
where I OUT is the LDO output current and C BSOUT is
the BSOUT capacitance.
Inductor Selection
The control scheme of the MAX5092/MAX5093 permits
flexibility in choosing an inductor value. Smaller induc-
tance values typically offer smaller physical size for a
given series resistance, allowing the smallest overall
circuit dimensions. Circuits using larger inductance
may provide higher efficiency and exhibit less ripple,
but also may reduce the maximum output current. This
occurs when the inductance is sufficiently large to pre-
vent the LX current limit (I LIM ) from being reached
before the maximum on-time (t ON-MAX ) expires.
For maximum output current, choose the inductor value
so that the controller reaches the current limit before
the maximum on-time is reached:
V × t ?
I LIM
where t ON-MAX is typically 2.25μs, and the current limit
ESR BSOUT =
Δ V ESRBS
I LIM ? I OUT
(I LIM ) is a maximum of 3A (see the Electrical
Characteristics). Choose an inductor with the maximum
saturation current (I SAT ) greater than 3A.
18
______________________________________________________________________________________
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
MAX620EWN
IC DVR QUAD HISIDE MOSFET 18SOIC
MAX626CPA+
IC DRIVER MOSFET DUAL 8-DIP
MAX662EVKIT-SO
EVAL KIT FOR MAX662
MAX6947ATE+T
IC LED DRIVER LINEAR 16-TQFN
MAX6948BGWA+T
IC LED DVR PWM GPIO 25WLP
MAX6964ATG+T
IC LED DRIVER LINEAR 24-TQFN
MAX6965ATE+T
IC LED DRIVER LINEAR 16-TQFN
MAX6967ATE+
IC LED DRIVER LINEAR 16-TQFN
相关代理商/技术参数
MAX5093
制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:4V to 72V Input LDOs with Boost Preregulator
MAX5093AATE+
功能描述:低压差稳压器 - LDO 4V to 72V LDO RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20
MAX5093AATE+T
功能描述:低压差稳压器 - LDO 4V to 72V LDO RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20
MAX5093BATE+
功能描述:低压差稳压器 - LDO 4V to 72V LDO RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20
MAX5093BATE+T
功能描述:低压差稳压器 - LDO 4V to 72V LDO RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20
MAX5094A
制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:High-Performance, Single-Ended, Current-Mode PWM Controllers
MAX5094AASA
功能描述:电流型 PWM 控制器 Single-Ended RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14
MAX5094AASA+
功能描述:电流型 PWM 控制器 Single-Ended RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14